Sintering of high wear resistant metal matrix compositesWEBER, Sebastian; THEISEN, Werner.Advanced engineering materials (Print). 2007, Vol 9, Num 3, pp 165-170, issn 1438-1656, 6 p.Article

Nucleation and precipitation kinetics of M₂₃C₆ and M₂N in an Fe―Mn―Cr―C―N austenitic matrix and their relationship with the sensitization phenomenonRONCERY, Lais Mujica; WEBER, Sebastian; THEISEN, Werner et al.Acta materialia. 2011, Vol 59, Num 16, pp 6275-6286, issn 1359-6454, 12 p.Article

Development of Mn-Cr-(C-N) Corrosion Resistant Twinning Induced Plasticity Steels: Thermodynamic and Diffusion Calculations, Production, and CharacterizationRONCERY, Lais Mújica; WEBER, Sebastian; THEISEN, Werner et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2010, Vol 41, Num 10, pp 2471-2479, issn 1073-5623, 9 p.Article

A novel PM-wear protection method to meet high comminution demandsTHEISEN, Werner.Wear. 2001, Vol 250-51, pp 54-58, issn 0043-1648, 1Conference Paper

Influence of Processing and Heat Treatment on Corrosion Resistance and Properties of High Alloyed Steel CoatingsHILL, Horst; WEBER, Sebastian; RAAB, Ulrich et al.Journal of thermal spray technology. 2012, Vol 21, Num 5, pp 987-994, issn 1059-9630, 8 p.Article

Gas―Solid Interactions During Nonisothermal Heat Treatment of a High-Strength CrMnCN Austenitic Steel Powder: Influence of Atmospheric Conditions and Heating Rate on the Densification BehaviorKRASOKHA, Nikolaj; WEBER, Sebastian; HUTH, Stephan et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2012, Vol 43, Num 11, pp 4237-4246, issn 1073-5623, 10 p.Article

Hot direct extrusion- : A novel method to produce abrasion-resistant metal-matrix compositesTHEISEN, Werner; KARLSOHN, Markus.Wear. 2007, Vol 263, Num 7-12, pp 896-904, issn 0043-1648, 9 p.Conference Paper

DIAMOND-METAL MATRIX INTERACTION IN TOOLS FABRICATED BY CONVENTIONAL AND CURRENT-INDUCED SINTERINGTILLMANN, Wolfgang; KRONHOLZ, Christian; FERREIRA, Manuel et al.International journal of powder metallurgy (1986). 2011, Vol 47, Num 4, issn 0888-7462, 29-36 [7 p.]Article

Microsegregation and Secondary Phase Formation During Directional Solidification of the Single-Crystal Ni-Based Superalloy LEK94LOPEZ-GALILEA, Inmaculada; HUTH, Stephan; FRIES, Suzana G et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2012, Vol 43, Num 13, pp 5153-5164, issn 1073-5623, 12 p.Article

High Velocity Oxy Fuel Spraying of Cold Work Tool Steels-A Novel Approach to Thick Coatings for Wear Protection ApplicationsRÖTTGER, Arne; WEBER, Sebastian L; THEISEN, Werner et al.Advanced engineering materials (Print). 2009, Vol 11, Num 12, issn 1438-1656, 953, 1015-1022 [9 p.]Article

A simplified micromechanical constitutive law adapted to the design of shape memory applications by finite element methodsPEULTIER, B; BEN ZINEB, T; PATOOR, E et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 384-388, issn 0921-5093, 5 p.Conference Paper

Characterization of the α ↔ β transformations in a Ti-6Al-2Sn-4Zr-6Mo (wt.%) alloyTARIN, P; ALONSO, I; SIMON, A. G et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 559-561, issn 0921-5093, 3 p.Conference Paper

Comparison of different methods for studying magnetic domains in Ni-Mn-Ga martensitesGE, Y; HECZKO, O; SÖDERBERG, O et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 302-305, issn 0921-5093, 4 p.Conference Paper

Effect of alloying on microstructure and shape memory characteristics of Cu-Al-Mn shape memory alloysMALLIK, U. S; SAMPATH, V.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 680-683, issn 0921-5093, 4 p.Conference Paper

Effect of annealing on cold-rolled Ni-Ti alloysSRIVASTAVA, Arvind K; ZHIQING YANG; SCHRYVERS, Dominique et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 594-597, issn 0921-5093, 4 p.Conference Paper

Finite-element modelling of shape memory alloys : A comparison between small-strain and large-strain formulationsCHRIST, D; REESE, S.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 343-346, issn 0921-5093, 4 p.Conference Paper

Heat treatment of TiNi wire used for intrauterine contraceptivesDORODEIKO, V. G; RUBANIK, V. V; RUBANIK, V. V et al.RUBANIK, V. V; RUBANIK, V. V et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 616-619, issn 0921-5093, 4 p.Conference Paper

High-temperature shape memory alloys based on the RuNb systemCHASTAING, K; DENQUIN, A; PORTIER, R et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 702-706, issn 0921-5093, 5 p.Conference Paper

In situ transmission electron microscopy of stress-induced martensite with focus on martensite twinningTIRRY, W; SCHRYVERS, D.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 420-425, issn 0921-5093, 6 p.Conference Paper

Influence of wire-drawing on the properties of a Cu-Al-Be polycrystalline shape memory alloyMUSSOT-HOINARD, G; PATOOR, E; EBERHARDT, A et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 538-541, issn 0921-5093, 4 p.Conference Paper

Martensitic transformation and shape memory effect under magnetic field for Ni₂MnGa sputtered films containing ironOHTSUKA, Makoto; KATSUYAMA, Hiroyuki; MATSUMOTO, Minoru et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 275-278, issn 0921-5093, 4 p.Conference Paper

Microstructural analysis on a creep resistant martensitic 9-12% Cr steel using the EBSD methodSONDEREGGER, B; MITSCHE, S; CERJAK, H et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 466-470, issn 0921-5093, 5 p.Conference Paper

Microstructure and shape memory behavior of annealed Ti-36.8 at.% Ni-11.6 at.% Cu thin filmISHIDA, A; SATO, M; OGAWA, K et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 91-94, issn 0921-5093, 4 p.Conference Paper

Microstructure of martensite in Fe-C-Cr steelYASO, Muneo; MORITO, Shigekazu; OHBA, Takuya et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 770-773, issn 0921-5093, 4 p.Conference Paper

Modeling of the variant reorientation in magnetic shape-memory alloys under complex magnetomechanical loadingKIEFER, B; LAGOUDAS, D. C.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 481-82, pp 339-342, issn 0921-5093, 4 p.Conference Paper